Battery chargers play an important role in ensuring optimum life and performance of Industrial Storage Batteries. Chloride chargers have been performing this duty relentlessly at different power plants, sub-stations, steel plants, refineries & petro chemicals,cement plants, oil & gas pipelines, telephone exchanges and many other industries for over last three decades.
Features-
✓
Microprocessor Controlled / Analog Controlled.
✓ Soft
Start feature.
✓
Battery path limiting current
✓
Automatic Float Boost Changeover
✓
Protection against AC phase reversal ,single phasing, A.C Under Voltage, Over Voltage, A.C Unbalance
✓
Dropper diode regulator in load path for specific application
✓
Psophometric noise 4 mV for specific application / requirement of Customer
✓
Seismic Test Certification
✓ Soak
Test / Environmental Test Certification
✓ Surge
with Stand capability as per ANSI-C37.90.1-2002
FLOAT CUM BOOST CHARGER ( FCB )
This is a special type of low cost charger for low voltage ranges. Only one converter is used. Under float mode this connects directly to the load bus along with battery floating to meet the DC loads at constant voltage. Under boost mode, battery will be charged at constant current rate. Load will be connected through the controlled dropper so that it (load) will not be affected by the boost voltage. In this system both float and boost charging is possible simultaneously through single converter.
FLOAT AND FLOAT CUM BOOST ( F&FCB )
The system consists of two converters for Float and Float cum Boost chargers.The primary function of the Float charger is to supply the connected DC load and simultaneously trickle charge the floating battery bank to keep it in fully charged state, so that it can supply the load during a power failure or any problem in input supply.The function of Float cum boost charger is to quick charge the battery after a heavy discharge and restores it to its full capacity within the shortest possible time and to supply the load in case of Float charger fails.
FLOAT AND BOOST ( F&B)
The Float charger is connected to the load bus directly and the Boost charger is connected to the battery. The Float charger will supply DC load at constant voltage. The Boost charger will quick (boost) charge the discharged battery at constant current as per requirement. The DC contactor (DC) is connected between battery and load bus. It will connect the battery to the load after completion of boost charge or on failure of the float charger or on failure of AC supply. Pick up time (200-500ms) of DC contactor may interrupt the load. Intermediate cell connected blocking diode (CD) ensures at least 80% of battery voltage during this interval .
DUAL FLAOT CUM BOOST( DFCB)
The system consists of two converters for Float and Float cum Boost chargers.The primary function of the Float charger is to supply the connected DC load and simultaneously trickle charge the floating battery bank to keep it in fully charged state, so that it can supply the load during a power failure or any problem in input supply.The function of Float cum boost charger is to quick charge the battery after a heavy discharge and restores it to its full capacity within the shortest possible time and to supply the load in case of Float charger fails.
| industrial chargers in Chandigarh Battery chargers play an important role in ensuring optimum life and performance of Industrial Storage Batteries. Chloride chargers have been performing this duty relentlessly at different power plants, sub-stations, steel plants, refineries & petro chemicals,cement plants, oil & gas pipelines, telephone exchanges and many other industries for over last three decades.
Features-
✓
Microprocessor Controlled / Analog Controlled.
✓ Soft
Start feature.
✓
Battery path limiting current
✓
Automatic Float Boost Changeover
✓
Protection against AC phase reversal ,single phasing, A.C Under Voltage, Over Voltage, A.C Unbalance
✓
Dropper diode regulator in load path for specific application
✓
Psophometric noise 4 mV for specific application / requirement of Customer
✓
Seismic Test Certification
✓ Soak
Test / Environmental Test Certification
✓ Surge
with Stand capability as per ANSI-C37.90.1-2002
FLOAT CUM BOOST CHARGER ( FCB )
This is a special type of low cost charger for low voltage ranges. Only one converter is used. Under float mode this connects directly to the load bus along with battery floating to meet the DC loads at constant voltage. Under boost mode, battery will be charged at constant current rate. Load will be connected through the controlled dropper so that it (load) will not be affected by the boost voltage. In this system both float and boost charging is possible simultaneously through single converter.
FLOAT AND FLOAT CUM BOOST ( F&FCB )
The system consists of two converters for Float and Float cum Boost chargers.The primary function of the Float charger is to supply the connected DC load and simultaneously trickle charge the floating battery bank to keep it in fully charged state, so that it can supply the load during a power failure or any problem in input supply.The function of Float cum boost charger is to quick charge the battery after a heavy discharge and restores it to its full capacity within the shortest possible time and to supply the load in case of Float charger fails.
FLOAT AND BOOST ( F&B)
The Float charger is connected to the load bus directly and the Boost charger is connected to the battery. The Float charger will supply DC load at constant voltage. The Boost charger will quick (boost) charge the discharged battery at constant current as per requirement. The DC contactor (DC) is connected between battery and load bus. It will connect the battery to the load after completion of boost charge or on failure of the float charger or on failure of AC supply. Pick up time (200-500ms) of DC contactor may interrupt the load. Intermediate cell connected blocking diode (CD) ensures at least 80% of battery voltage during this interval .
DUAL FLAOT CUM BOOST( DFCB)
The system consists of two converters for Float and Float cum Boost chargers.The primary function of the Float charger is to supply the connected DC load and simultaneously trickle charge the floating battery bank to keep it in fully charged state, so that it can supply the load during a power failure or any problem in input supply.The function of Float cum boost charger is to quick charge the battery after a heavy discharge and restores it to its full capacity within the shortest possible time and to supply the load in case of Float charger fails.
Battery chargers play an important role in ensuring optimum life and performance of Industrial Storage Batteries. Chloride chargers have been performing this duty relentlessly at different power plants, sub-stations, steel plants, refineries & petro chemicals,cement plants, oil & gas pipelines, telephone exchanges and many other industries for over last three decades.
Features-
✓
Microprocessor Controlled / Analog Controlled.
✓ Soft
Start feature.
✓
Battery path limiting current
✓
Automatic Float Boost Changeover
✓
Protection against AC phase reversal ,single phasing, A.C Under Voltage, Over Voltage, A.C Unbalance
✓
Dropper diode regulator in load path for specific application
✓
Psophometric noise 4 mV for specific application / requirement of Customer
✓
Seismic Test Certification
✓ Soak
Test / Environmental Test Certification
✓ Surge
with Stand capability as per ANSI-C37.90.1-2002
FLOAT CUM BOOST CHARGER ( FCB )
This is a special type of low cost charger for low voltage ranges. Only one converter is used. Under float mode this connects directly to the load bus along with battery floating to meet the DC loads at constant voltage. Under boost mode, battery will be charged at constant current rate. Load will be connected through the controlled dropper so that it (load) will not be affected by the boost voltage. In this system both float and boost charging is possible simultaneously through single converter.
FLOAT AND FLOAT CUM BOOST ( F&FCB )
The system consists of two converters for Float and Float cum Boost chargers.The primary function of the Float charger is to supply the connected DC load and simultaneously trickle charge the floating battery bank to keep it in fully charged state, so that it can supply the load during a power failure or any problem in input supply.The function of Float cum boost charger is to quick charge the battery after a heavy discharge and restores it to its full capacity within the shortest possible time and to supply the load in case of Float charger fails.
FLOAT AND BOOST ( F&B)
The Float charger is connected to the load bus directly and the Boost charger is connected to the battery. The Float charger will supply DC load at constant voltage. The Boost charger will quick (boost) charge the discharged battery at constant current as per requirement. The DC contactor (DC) is connected between battery and load bus. It will connect the battery to the load after completion of boost charge or on failure of the float charger or on failure of AC supply. Pick up time (200-500ms) of DC contactor may interrupt the load. Intermediate cell connected blocking diode (CD) ensures at least 80% of battery voltage during this interval .
DUAL FLAOT CUM BOOST( DFCB)
The system consists of two converters for Float and Float cum Boost chargers.The primary function of the Float charger is to supply the connected DC load and simultaneously trickle charge the floating battery bank to keep it in fully charged state, so that it can supply the load during a power failure or any problem in input supply.The function of Float cum boost charger is to quick charge the battery after a heavy discharge and restores it to its full capacity within the shortest possible time and to supply the load in case of Float charger fails.